Perle eX-SM1110 Managed Gigabit Ethernet Extenders

SPHINX in Europe
BE
  • AT
  • BE
  • DK
  • FR
  • DE
  • IE
  • IT
  • NL
  • ES
  • SE
  • CH
  • UK
Product groups > Mediaconverter > Perle eX-SM1110 Managed Gigabit Ethernet Extenders

Perle eX-SM1110 Managed Gigabit Ethernet Extenders

Managed Long Range LAN Extender

Perle eX-SM1110 Managed Gigabit Ethernet Extenders
3440_23641.png
3440_23642.gif
  • PropertiesProperties
  • DescriptionDescription
  • Further InformationFurther Information
  • PDFPDF
  • Extends 10/100/1000Base-T Ethernet up to 10,000 feet ( 3 KM ) over 2-wire 24 AWG twisted pair.
  • Hi-Speed – up to 200+ mbps aggregate bandwidth
  • Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes.
  • Advanced features - Link Pass-Through, Interlink Fault Feedback, Auto-MDIX and Loopback
  • Manage via SNMP, CLI - Telnet/SSH, Internet browser, or
  • PerleVIEW Centralized Management Package
10/100/1000 Ethernet Extenders allow you to extend Ethernet services beyond the general IEEE 802.3 limits of 328ft / 100m using any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications. For environments where the 10/100/1000 LAN is being extended and network security is critical, Perle offers Managed Gigabit Ethernet Extenders that support all authentication, authorization and accounting (AAA) security services used in corporate networks, including TACACS+, RADIUS, LDAP, Kerberos, NIS and RSA. To further protect ID’s and passwords from someone ‘snooping’ on the network, Perle Managed Ethernet Extenders provide secure management sessions by supporting SSH, SNMPv3, Telnet and HTTPS. These types of features are used when managing your corporate firewalls, switches and routers. This is why Perle makes them available in the eX-SM1110 Managed Ethernet Extender.

These simple and effective point to point Ethernet Copper Extenders are perfect for commercial buildings, residential units, hospitality environments and remote offices … anywhere you need the ability to securely configure, monitor and manage long range Ethernet communication links between separated LANs or LAN devices (i.e. PCs, digital sensors, VoIP phones, WiFi Access Points, IP cameras and more).

You will also appreciate how easy it is to set up the eX-SM1110 with an intuitive Web Manager GUI and multiple methods of access. And, with support for IPv6, Perle Managed Ethernet Extenders provide organizations with investment protection to meet this rapidly growing standard. For high density applications check out the eX-CM1110 Managed Fast Ethernet Extender Modules.

10/100/1000 Ethernet Extenders are also available as unmanaged standalone models with support for Commercial Temperature ranges and Extended Temperature ranges.

eX-SM1110 Managed Gigabit Ethernet Extender Features

Perle’s advanced features such as Link Pass-Through, Interlink Fault Feedback, and Loopback allow Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle eX-SM1110 Managed Ethernet Extenders the smart choice for IT professionals.

Management Module Indicators / reset

    Power
    Blinking green during startup cycle
    Steady green: module has power and is ready
    Red : error

    ALM
    Red alarm indicator activated when an alert event occurs

    LKC
    Green indicator indicating an active Ethernet link. Blinking indicates RX and TX of data

    100/1000
    Green - 1000 Mbps link
    Yellow - 100 Mbps link
    Off - 10 Mbps or no Link

    Reset button
    Recessed pinhole button resets module


Ethernet

    Port
    1 port RJ45 – 10/100 Base-TX - Shielded

    Auto-MDIX
    Auto-MDIX enables proper operation with either straight-through or crossover cabling

    Distance
    Distance up to 100 meters ( 328 feet ) as per IEEE 802.3

    Maximum Frame Size
    1522 bytes


VDSL - Interlink

    RJ45, BNC, Terminal Block
    TIP and RING are polarity insensitive. Surge suppresion of 400 volts between TIP and RING
    Choice of RJ45, BNC or terminal block models for VDSL link connector
    • RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
    • BNC – Coaxial 75 ohm cable with BNC connector
    • Terminal Block – 2 position screw connectors for use with twisted pair telephone cabling

    Cabling
    Ethernet Extenders must be connected in pairs using unconditioned wire between 19 ( 0.9 mm ) and 26 AWG ( 0.44 mm ). Circuits that run through signal equalization equipment are not permitted.


Indicators

    Power / TST
    This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.

    CO - Local
    Ethernet Extender is operating in CO VDSL mode

    CPE - remote
    Ethernet Extender is operating in CPE VDSL mode

    ILNK
    Indicates Link Status and activity on the Interlink (VDSL) port

    ETH
    Indicates link status and activity on Ethernet port.


Switches - On-board PCB

    Rate/Reach
    Two switches enable the user to select the right balance between speed and distance for their environment.

    Signal to Noise Ratio
    Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.

    Auto-Negotiation (802.3u)
    Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex.
    Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.

    Link Mode
    Standard (Default) – The 10/100/1000Base-T link remains active independent of the state of the Ethernet link on its remote peer.
    Link Pass-Through- the state of the 10/100/1000Base-T Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100/1000Base-T Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.

    Interlink Fault Feedback
    Enabled - A loss of VDSL link will drop the 10/100 Ethernet port on each end until the link recovers
    Disabled ( Default ) – The state of the VDSL link is not propagated to the 10/100/1000Base-T port

    Loopback
    Enabled - The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer.
    Disabled (Default - Up)

    Set Ethernet Speed
    When Auto-Negotiation switch is disabled, fixed speed can be set at 100 (Default) or 10

    Set Ethernet Duplex
    When Auto-Negotiation switch is disabled, Duplex can be set at Full (Default) or Half


Power

    Input Voltage
    12 vDC ( nominal )

    Current
    560ma @ 12 vDC

    Power Consumption ( Watts )
    6.7

    Power Connector
    5.5mm x 9.5mm x 2.1mm barrel socket

    AC Adapter
    100-240v AC, regulated DC adapter included


Environmental Specifications

    Operating Temperature
    0 C to 50 C (32 F to 122 F)

    Storage Temperature
    minimum range of -25 C to 70 C (-13 F to 158 F)

    Operating Humidity
    5% to 90% non-condensing

    Storage Humidity
    5% to 95% non-condensing

    Operating Altitude
    Up to 3,048 meters (10,000 feet)

    Heat Output ( BTU/HR )
    22.86

    MTBF (Hours)*
    221,305 w/o adapter
    156,656 w/ adapter


Packaging

    Shipping Weight
    1.2 Kg, 2.6 lbs

    Shipping Dimensions
    200 x 300 x 70 mm, 7.9 x 11.8 x 2.8 inches


Regulatory Approvals

    Emissions
    FCC Part 15 Class A, EN55022 Class A
    CISPR 22 Class A
    EN61000-3-2

    Immunity
    EN55024

    Electrical Safety
    UL 60950-1
    EN60950
    CE

    Environmental
    Reach, RoHS and WEEE Compliant

    Other
    ECCN: 5A991A
    HTSUS Number: 8517.62.0050
    Perle Lifetime warranty



eX-1SM1110-RJ
Gigabit Ethernet IP-Managed Stand-Alone Ethernet Extender
1 port 10/1001000Base-T (RJ-45) [100 m/328 ft.]. RJ45 Interlink ( VDSL2 ) connector


eX-1SM1110-BNC
Gigabit Ethernet IP-Managed Stand-Alone Ethernet Extender
1 port 10/1001000Base-T (RJ-45) [100 m/328 ft.]. BNC ( Coax ) Interlink ( VDSL2 ) connector


eX-1SM1110-TB
Gigabit Ethernet IP-Managed Stand-Alone Ethernet Extender
1 port 10/1001000Base-T (RJ-45) [100 m/328 ft.]. 2-pin Terminal Block Interlink ( VDSL2 ) connector



Customers who viewed this item also viewed
Accept all Reject Configure

This website uses cookies to provide the best possible experience. More information.